Читать книгу Piston Engines of the New Generation (Without turbo – supercharging) - Anatoly Matveevich Druzhinin - Страница 6

From the losses considered, it is necessary to highlight, as priority, gas-dynamic losses that affect the main working processes occurring in the combustion chamber and in the engine cylinder, as a result, on the efficiency of the engine.

The researches have shown that when analysis of various losses characteristic of the internal combustion engine and affecting on the value of its efficiency, the main task was to determine the location of each of them identify the priorities and influence on other groups of losses. Two groups of losses – mechanical and gas dynamic apply for the first post.

Let’s start with the dynamics. The domestic scientists and specialists mechanics, belong indulgently to gas dynamics as to the factor exerting serious impact on work of the ICE. In the best case, the gas dynamics for them is “leakage of the working gas”, determined for a single piston ring [5].

An analysis of the accuracy and value of the gaps in domestic engines shows that the theoretical calculations of the German scientist in determining the value of “leakage of working gas” have not found wide application in our country. – In the following, we consider some constructions, where the role of “leaks” is reduced to an insignificant minimum.

Turn to the materials in the domestic textbooks. “When the ring is compressed and inserted into the cylinder, it takes a cylindrical shape and exerts a pressure on the cylinder walls equal to 0,05 … 0,3 MPa (0,5 … 3 kg / cm²) and more. During operation, the pressure increases of the ring on the walls, since gases penetrating through the gaps between the ring and the piston press the ring against the wall of the cylinder”[6].

About the same, in 10 years. “The sealing is carried out by pressing the ring against the cylinder wall by the elasticity of the ring and the pressure of the gases. At the moment of flare when the piston is in upper dead center (UDC), the pressure in the groove of the 1st ring is close to the pressure P_z in the cylinder, and in the groove of the 2nd ring it is only 50% of this value. Pressure P₃ behind the last ring is much smaller; it is commensurate with the pressure in the crankcase of the engine. In view of the considerable pressure of the rings on the cylinder walls, the majority of the work of friction in the engine (up to 50%, and sometimes up to 60%) falls on the rings, so it is impossible to press the rings with excessive force”[7].

The conclusions drawn by scientists on the one hand are quite obvious, and on the other hand inferior, are of a general nature, having little effect on the process of designing the piston rings. There is no answer to the main question: how, and with what efforts does the pressure of working gases in the cylinder act on the sealing piston ring?

The process of constantly changing pressure of intake air into a cylinder, then mixed together with the fuel in the combustion chamber and transfused into working gases, should be considered as a gas dynamic process.

In 2004 for the first time the author published the gas-dynamic scheme of operation of the compression ring of the KAMAZ engine on the basis of an analysis of the established attitude of scientists and specialists of mechanics to gas dynamics [1]. This is how the design and position of the compression ring look without any slopes of the upper end face and chamfers along the inner diameter (Figure 1).

It was necessary to remember and use the known physical law, in the appendix to the given case it can sound as follows:

On the free surfaces of the piston ring (upper end and inside vertical surface) located in the closed space limited to a cylinder wall, a bottom of a piston groove and its upper and lower shelves which is under pressure of working gases, there are forces proportional to the areas of these surfaces

Figure. 1. The gas dynamic scheme of the operation of the compression ring of the KAMAZ engine: 1-A CYLINDER 2-A PISTON; 3-A PISTON RING

Breaking through the gap between the piston 2 and the cylinder 1 into the upper piston groove, the working pressure presses the piston ring 3 to the lower shelve of the piston groove with the gas-dynamic force F₀, and to the cylinder wall by the radial force F_rad and the force of intrinsic elasticity F _seal. The calculation of these forces was provided in the author’s previous publications.

The most interesting can be seen in this calculation for one of the most popular domestic engines of VAZ-2190, with the following parameters: the maximum pressure of the working gases in the cylinder when the piston is at top dead center, is about P_work = 80 kg / cm². The dimensions are in centimetres for convenience of calculations. Diameter of the cylinder is 82 mm = 8.2 cm; the outer radius r₁ is 41 mm = 4.1 cm; the inner radius is r₂—38 mm = 3.8 cm; the radial thickness of the ring t = 3.0 mm = 0.3 cm; the height of the upper compression ring h = 1.5 mm = 0.15 cm.

The area of the upper butt is defined by the formula:

S₁ = π (r₁²-r₂²) = 3.14 (4.1²—3.8²) = 3.14 (16.81—14.44) = 7.44 cm².

The area of the inner vertical surface is defined by the formula: S₂ = 2 πr₂h = 6.28 × 3.8 × 0.15 = 3.58 cm².

Multiplying the pressure of the working gases by the area values, we get:

F_o = P_work × S₁ = 80 × 7.44 = 595.2 kgf (5.95 kN);

F_rad = P_work × S₂ = 80 × 3.58 = 286.4 kgf (2.86 kN).

The conclusion is obvious from the comparison of these two gas-dynamic forces acting on the movable piston ring. Twice the superior axial force reliably pressed the piston ring to the lower flange of the piston groove, depriving the radial force of the working surface of the piston ring from being pressed against the wall of the cylinder.

That is very important to note here. This pattern is observed in all cases where there is an excessive pressure on the piston. About this and not only, we will consider on the different steps of the engine motoring run. But now, running ahead, we can safely predict:

The gas dynamic scheme fundamentally changed the strategy and tactics, the theory and practice of designing internal combustion engines and piston compressors. It optimizes the size, shape and content of the engine and compressor and is reflected in the increase in the efficiency of both with its correct application in calculations.

All justifications are given in the author’s work and in this manual. The information were published and patented, brought to the attention of scientists and specialists of the motors. However, producers continue to “produce” super modern cars equipped with the engines with such significant defects. Let’s try again, to spell out in more detail the problem of increasing the efficiency of the internal combustion engines, which is not so difficult to understand, but very important for specialists.